 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1/9 www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. audio accessory ics preamps with built-in alc ba3308f,ba3308fv description the ba3308f/fv is a dual preamplifier for recording and playback with alc (auto level control) , developed for stereo radio, cassette recorders, tape recorders, and other pre amplifiers audio applications. alc circuit has a build in rectification circuit with wide adjust able dynamic range, high gain, lo w distortion amplifiers with direct coupling and mute circuit, used to cut off pop noise during power on. available in sop14, or ssop-b14 packages. features 1) built-in alc rectification diode 2) wide operating power supply voltage range (v cc =4.5~14 v) 3) low current consumption (i q =3.5ma) 4) high gain (g vo =80db) 5) low distortion (thd=0.1%) 6) low noise (v nin =1 v rms ) 7) input coupling capacitor not needed 8) good alc channel balance 9) built-in power supply mute circuit 10) dynamic range of alc can be changed by attaching input resistance. applications stereo radio, cassette tape recorders, stereo ca ssette decks, home stereos, music centers, etc. line up matrix part no. ba3308f ba3308fv package sop14 ssop-b14 no.11087ect01
technical note 2/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. absolute maximum ratings (ta=25 ? ? ? ? operating conditions (ta=25 electrical characteristics (unless otherwise noted, ta=25 technical note 3/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. nf1 input1 output1 gnd alc v cc output2 input2 nf2 alc v cc 1 2 3 4 5 6 7 14 13 12 11 10 9 8 ? ? ? ? block diagram fig.1 technical note 4/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. electrical characteristic curves (reference data) fig.2 quiescent current vs. technical note 5/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. description of operations 1. recording 1) record amplifier 2) alc fig.5 ba3308 cont ch2 (ch1) ch2 (ch1) ch1 (ch2) 2 (8) 1 (9) 3 (7) 5 3.9k ? ? ? ? ? ? ? ? P ? technical note 6/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. 2. on playback ? fig.7 a1 ba3308 2 (8) 10 39 : 1 (9) 3 (7) 5 input output r 3 (r 4 ) c 9 (c 10 ) (c 6 ) c 5 10 c 1 100 c 3 r 11 (r 12 ) 4.3k : r 9 (r 10 ) 120k : 13(9) 11(10) 1 (7) 4 fig.16 technical note 7/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. measurement circuit application circuit fig.18 for playback, connect the following n ab time constant circuit between pins 11 and 1 and pins 10 and 7 in place of r5 and r6. input1 input2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 alc 10 ? ? ? ? ? ? ? ? ? ? ? ? ? ? technical note 8/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. notes for use 1) numbers and data in entries are representative desi gn values and are not guaranteed values of the items. 2) although rohm is confident that t he example application circuit reflects the best possible recommendations, be sure to verify circuit characteristics for your particular applicat ion. modification of constants for other externally connected circuits may cause variations in both static and transient ch aracteristics for external components as well as this rohm ic. allow for sufficient margins when determining circuit constants. 3) absolute maximum ratings use of the ic in excess of absolute maximum ratings, such as the applied voltage or operating temperature range (topr), may result in ic damage. assumptions should not be made regarding the state of the ic (short mode or open mode) when such damage is suffered. a physical safety meas ure, such as a fuse, should be implemented when using the ic at times where the absolute maximum ratings may be exceeded. 4) gnd potential ensure a minimum gnd pin potential in all operating conditi ons. make sure that no pins are at a voltage below the gnd at any time, regardless of whether it is a transient signal or not. 5) thermal design perform thermal design, in which there are adequate margins, by taking into account the permissible dissipation (pd) in actual states of use. 6) short circuit between terminals and erroneous mounting pay attention to the assembly direction of the ics. wrong mounting direction or shorts between terminals, gnd, or other components on the circuits, can damage the ic. 7) operation in st rong magnetic fields using the ics in a strong electromagnetic field can cause operation malfunction. technical note 9/9 ba3308f,ba3308fv www.rohm.com 2012.06 - rev.c ? 2011 rohm co., ltd. all rights reserved. ordering part number b a 3 3 0 8 f - e 2 part no. part no. package f: sop14 fv: ssop-b14 packaging and forming specification e2: embossed tape and reel (unit : mm) sop14 7 14 1.27 0.11 1 8 0.3min 8.7 0.2 0.4 0.1 0.15 0.1 1.5 0.1 6.2 0.3 4.4 0.2 (max 9.05 include burr) 0.1 ? order quantity needs to be multiple of the minimum quantity. datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (?specific applications?), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, ro hm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hm?s products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohm?s products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified bel ow), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range descr ibed in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used; if flow soldering met hod is preferred, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin c onsidering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a hum idity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohm?s internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contain ed in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. datasheet datasheet notice ? we rev.001 ? 2014 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. datasheet part number ba3308f package sop14 unit quantity 2500 minimum package quantity 2500 packing type taping constitution materials list inquiry rohs yes ba3308f - web page distribution inventory |
Price & Availability of BA3308FV-E2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |